Ametek CW Series Programming Manual Instrukcja Użytkownika

Contact Information Telephone: 800 733 5427 (toll free in North America) 858 450 0085 (direct) Fax: 858 458 0267 Em

Programming Manual 3-1 SECTION 3 SCPI COMMANDS 3.1 Miscellaneous Commands :ASSYno? Returns the assembly number. 3.2 MEASURE Commands :MEASure [p

SCPI Commands Elgar CW-P Series 3-2 Programming Manual 3.3 OUTPUT Commands :OUTPut? Return the state of the output relay. :OUTPut <boolean>

Elgar CW-P Series SCPI Commands Programming Manual 3-3 :FREQuency <value> Set the frequency of the CW. :FREQuency? Returns the freque

SCPI Commands Elgar CW-P Series 3-4 Programming Manual 3.5 STATUS Commands :STATus The status commands tree. :OPERation? SCPI commands return

Elgar CW-P Series SCPI Commands Programming Manual 3-5 :STORe? Return the present EEPROM register address that was read to set the present se

SCPI Commands Elgar CW-P Series 3-6 Programming Manual 3.8 Common Commands The following commands are common to all SCPI instruments and declare

Programming Manual 4-1 SECTION 4 RS-232 INTERFACE This section describes how to connect the CW-P for remote programming with a controller using the

RS-232 Interface Elgar CW-P Series 4-2 Programming Manual 4.3 RS-232 Connector The RS-232 connector is a 9-pin male Subminiature-D type; its pinout

Programming Manual A-1 APPENDIX A STATUS REGISTER DEFINITIONS The CW-P Series supports the IEEE 488.2 and SCPI 1993.0 status reporting data structur

Status Register Definitions Elgar CW-P Series A-2 Programming Manual Bit 2, Error/Event Queue Information Available This bit is set when any error/e

Elgar CW-P Series Status Register Definitions Programming Manual A-3 Operation Complete Set whenever the last command is completed and the CW is rea

Status Register Definitions Elgar CW-P Series A-4 Programming Manual This page intentionally left blank.

Programming Manual B-1 APPENDIX B ERROR CODES B.1 Error Codes Returned by SYSTem:ERRor? Query The following error codes are defined in the SCPI 199

Error Codes Elgar CW-P Series B-2 Programming Manual -200, Execution error An error/event number in the range [-299, -200] indicates that an error

Programming Manual C-1 APPENDIX C SAMPLE PROGRAMS The following examples will illustrate how to perform certain functions on the CW-P using SCPI via

Sample Programs Elgar CW-P Series C-2 Programming Manual 8. Turn On RMS loop SOUR:VOLT:RMSLOOP ON (1) 9. Turn Off RMS loop SOUR:VOLT:RMSLOOP O

Contents Elgar CW-P Series Programming Manual i CONTENTS SECTION 1 SCPI CONFORMANCE INFORMATION ... 1-1 1.1 Introduc

Elgar CW-P Series Contents ii Programming Manual SECTION 4 RS-232 INTERFACE ... 4-1 4.1 RS-2

Programming Manual 1-1 SECTION 1 SCPI CONFORMANCE INFORMATION 1.1 Introduction This manual provides programming information for Elgar‟s ContinuousW

SCPI Conformance Information Elgar CW-P Series 1-2 Programming Manual 1.4 Conventions Commands enclosed by “[ ]” are optional. For example, SOURc

Programming Manual 2-1 SECTION 2 POWER-ON AND RESET CONDITIONS The following sections define the factory and reset power-on conditions of the unit.

Power-On and Reset Conditions Elgar CW-P Series 2-2 Programming Manual In addition, unique system settings are read in from the non-volatile EEROM m