Ametek ReFlex Programming Manual Instrukcja Użytkownika Strona 87
- Strona / 134
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
DC Module Remote Programming ReFlex Power™ Programming Manual
M380056-03 Rev L 83
Co
mmand
Description
:
CLOSe
Opposite of LIST:OPEN, disables the currently open list. Clears
the LIST<n>:ERR? and LIST<n>:STATUS? error responses.
:
ARM
Start module <n> executing the list upon receipt of this command.
:
TAG <NRi>
Creates a user queriable numeric marker in the LIST during list
execution. NRi = 1-1023.
:
TAG?
2
Returns the last encountered numeric marker that has been
“executed” in the list. Used to track where module <n> is in the
list sequence, during execution. During List creation, returns
memory usage, up to 2040 instruction index units are allowed.
:
STATUS?
Returns Script status of EXEC, IDLE, or STOP/FAULT.
:
ERRor?
Returns: Status, Errors, Tag, & Instruction Index.
:
LABEL<0-31>
32 Labels can be defined. Forward and backward LABEL
references are allowed.
:
GOTO LABEL<0-31>
GOTO LABEL<0-31>; List execution immediately continues at the
referenced label.
:
LOOP <+NRi>, LABEL<0-31>
Jump <NRi+> times to LABEL<0-31>. Used to repeat a sequence
of events. Repeat count +NRi is 1 to 16777215.
:
DWELl <+NRf>
Sets the dwell time, the period that LIST execution pauses, in
module <n> for +NRf seconds.
1.0e-6 <= +NRf <= 2147.48 seconds.
:
TRIGger <t>, WAIT
Module <n> waits for a trigger, <t> = a, b, c, or d, for Buss trigger
in’s, or fa to wait on the module’s Front Panel trigger in.
Tracking MUST be OFF during RAMPs
:RAMP
Ramp Generation
:CURR fIstart, fIend, ftSec
Generate a CURRent RAMP from fIstart, to fIend Amps, in ftSec
Seconds. Note: Full scale excursions take about 100mSec, and
are load dependent, smaller current excursions are proportional.
:VOLT fVstart, fVend, ftSec
Generate a VOLTage RAMP from fVstart, to fVend Volts, in ftSec
seconds. Note: Full scale excursions take about 20mSec
depending on type of load, smaller voltage excursions are
proportional.
:VOLTCURR fVstart, Vend,
fIstart, fIend, ftSec
Generate a VOLTage and CURRent RAMP from fVstart to fVend
Volts, and from fIstart, to fIend Amps, in ftSec seconds.
:CURR GE fval, LABEL
<
0-31
>
Branch to LABEL<n> if the output current is ≥ to fval.
:CURR LT fval, LABEL
<
0-31
>
Branch to LABEL<n> if the output current is < fval.
:VOLT GE fval, LABEL
<
0-31
>
Branch to LABEL<n> if the output voltage is ≥ to fval.
:VOLT LT fval, LABEL
<
0-31
>
Branch to LABEL<n> if the output voltage is < fval.
1
<filename> is case sensitive; a double quoted string, maximum 29 characters in length, no path/file
extension
is allowed.
NOTE: ftSec is 0.1mS to 2147.48 seconds. (35.791 minutes)
Any triggers that occur during a RAMP or DWELL command are ignored.
In List mode, all relay operation should always be coordinated with the STATE command by using
the OUTP:ISOL/SENSE:DEFault commands.
If Tracking is ON, (OVP, OCP, UVP) their setting changes will automatically be included in the LIST
commands for simple setpoint changes.
- ReFlex Power™ 1
- (“AMETEK”): 5
- SAFETY SYMBOLS 7
- CONTENTS 11
- LIST OF TABLES 17
- LIST OF FIGURES 18
- REMOTE PROGRAMMING OVERVIEW 19
- 1.4.1 F 21
- 18 M380056-03 Rev M 22
- CONTROLLER MODULE REMOTE 23
- CONFIGURATION 24
- THERNET 25
- ROCEDURE 25
- 2.4.3 L 26
- M380056-03 Rev L 23 27
- 2.5.1 H 28
- 2.5.2 LOGIN 29
- 2.5.3 IP 30
- 28 M380056-03 Rev M 32
- 2.5.4 S 33
- 2.5.5 M 36
- Figure 2-13. Net Test Window 37
- 2.6.1 M 39
- SCPI COMMAND OPERATION 40
- 2.8.4 Q 43
- EIB SCPI COMMANDS 45
- SYSTEM:NETWORK SCPI COMMANDS 46
- 2.11.2 SYSTEM:NETWORK 47
- RFP SERVICE REQUEST 48
- XECUTION TIME 50
- PERATION 50
- RELATED 51
- 48 M380056-03 Rev M 52
- ETTING THE 53
- BIT IN THE 53
- AN EXAMPLE 53
- TRIGGER SCPI COMMANDS 54
- MEMORY SCPI COMMANDS 55
- 52 M380056-03 Rev M 56
- DC MODULE REMOTE PROGRAMMING 57
- :LOCK 62
- 3.9.2 SOURCE 67
- XTERNAL 72
- RIGGERING 72
- SCPI Command Description 74
- ‘fa’, ‘b’ to ‘fb’… 74
- 72 M380056-03 Rev M 76
- Figure 3-8. List Mode Logic 78
- 78 M380056-03 Rev M 82
- LIST SCPI COMMANDS 86
- 84 M380056-03 Rev M 88
- DC SYSTEM SCPI COMMANDS 89
- 88 M380056-03 Rev M 92
- AC MODULE REMOTE PROGRAMMING 93
- 4.4.2 E 96
- 4.6.2 CALIBRATION 100
- MEASURE SCPI COMMANDS 103
- OUTPUT SCPI COMMANDS 104
- SOURCE SCPI COMMANDS 105
- EFERENCE 106
- cross waveform 107
- STATUS SCPI COMMANDS 110
- M380056-03 Rev L 107 111
- SYSTEM SCPI COMMANDS 112
- PARALLEL GROUPS 112
- 4.12.2 E 113
- 110 M380056-03 Rev L 114
- LOAD MODULE REMOTE 115
- PROGRAMMING 115
- POWER-ON CONDITIONS 116
- ERROR CODES 117
- COMMON SCPI COMMANDS 118
- CALIBRATION SCPI COMMANDS 119
- 5.6.2 CALIBRATION 120
- INPUT SCPI COMMANDS 122
- FIXED POWER DC REMOTE 127
- 6.5.2 CALIBRATION 131
- STATUS COMMANDS 133
- SYSTEM COMMANDS 133
- 130 M380056-03 Rev L 134
Powiązane produkty i podręczniki dla Ekwipunek Ametek ReFlex Programming Manual
Ekwipunek Ametek ReFlex Instrukcja Użytkownika
(359 strony)
(359 strony)
Ekwipunek Ametek SGI Series Instrukcja Użytkownika
(128 strony)
(128 strony)
Ekwipunek Ametek SLM-1 Instrukcja Użytkownika
(77 strony)
(77 strony)
Ekwipunek Ametek SLM-4 Instrukcja Użytkownika
(77 strony)
(77 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji