Ametek BPS Series Programming Manual Instrukcja Użytkownika Strona 74
- Strona / 226
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
AMETEK Programmable Power BPS / MX / RS Series SCPI Programming Manual
74 Manual P/N 7003-961 Rev AA
OUTPut:IMMediate
This command opens the output relay without first programming the voltage down if the –
SNK option is installed and the MX/RS/BPS is in REGENERATIVE mode (REG:STAT ON).
If not, this commands works exactly the same as the OUTP[:STAT] command. This mode
may be used to simulate line loss in inverter applications. The query form returns the output
state.
Command Syntax OUTPut:IMMediate<bool>
Parameters 0 | OFF | 1 | ON
*RST Value OFF
Examples OUTP:IMM 1 OUTP:IMM OFF
Query Syntax OUTPut:IMMediate?
Returned Parameters 0 | 1
Related Commands REG:STAT REG:CURR
4.11.2 Output Protection
OUTPut:PROTection:CLEar
Available on MX/RS/BPS Series II only. This command clears the latch that disables the
output when an overvoltage (OV), overcurrent (OC), overtemperature (OT), or remote inhibit
(RI) fault condition is detected. All conditions that generated the fault must be removed
before the latch can be cleared. The output is then restored to the state it was in before the
fault condition occurred.
Command Syntax OUTPut:PROTection:CLEar
Parameters None
Examples OUTP:PROT:CLE
Related Commands OUTP:PROT:DEL *RCL *SAV
4.11.3 Output Remote Inhibit Modes
OUTPut:RI[:LEVel]
This command sets the remote inhibit level mode. Factory default is LOW, which requires a
contact closure to open the output relay. The level can be reversed by setting it to HIGH.
Once set, the RI level setting is retained each time the power source is powered up. Note
that this command is only implement with firmware revision 0.28 or higher. Lower firmware
revisions only provide the default LOW setting (MX15 excluded).
Command Syntax OUTPut:RI:LEVel
Parameters LOW | HIGH
*RST Value LOW
Examples OUTP:RI:LEV HIGH
Query Syntax OUTP:RI:LEV?
Returned Parameters <CRD>
Related Commands OUTP
NOTE: When using the Remote Inhibit input, it will be necessary to disconnect any RI
connection to the MX/RS/BPS master unit when turning on the MX/RS/BPS
master unit. During initialization, the RI connection must be OPEN
or
initialization will be halted with the message WAITING FOR AUXILIARY
displayed on the LCD screen.
- BPS / Mx / RS Series 1
- SCPI Programming Manual 1
- WARNING 4
- SAFETY SYMBOLS 5
- Warranty Period: 1 Year 6
- WARRANTY TERMS 6
- PRODUCT RETURN PROCEDURE 6
- Table of Contents 7
- Table of Figures 9
- Table of Tables 9
- Introduction 10
- Model BPS Series 11
- External References 11
- Introduction to Programming 12
- Introduction to SCPI 14
- Types of SCPI Messages 15
- The SCPI Command Tree 15
- Using Queries 17
- Structure of a SCPI Message 17
- The Message Unit 17
- Combining Message Units 18
- Headers 19
- Query Indicator 19
- Message Unit Separator 19
- Root Specifier 20
- Message Terminator 20
- SCPI Data Formats 21
- Numerical Data Formats 21
- Character Data 21
- GPIB Controllers 22
- Agilent 82350 Driver 22
- RS232C Interface 24
- Serial Cable Diagram 25
- USB Driver Installation 26
- USB Interface 26
- USB Interface Use 34
- LAN Interface Option 35
- MAC Address 35
- Setting the TCP/IP Address 35
- Socket Port Number 37
- IP Ping 37
- SCPI Command Reference 38
- Calibration Subsystem 39
- [:SOURce] 40
- :HRANge 40
- :IMPedance 40
- Current Measurement 42
- Voltage Measurement 44
- Output Phase 46
- Output - AC Voltage 47
- Output - DC Voltage 49
- Display Subsystem 51
- Instrument Subsystem 53
- Current Array Data 56
- Voltage Array Data 60
- Phase Measurement Subsystem 67
- Power Measurement Subsystem 68
- Output Subsystem 73
- Output Relay 73
- Output Protection 74
- Output Remote Inhibit Modes 74
- External Trigger Output 76
- Source Subsystem - Current 79
- Source Subsystem - Frequency 81
- Source Subsystem - Limit 86
- Source Subsystem - List 90
- List - Count 91
- List - Dwell 91
- List - Frequency 92
- List - Repeat 94
- List - Step 94
- List:TTL Trigger Out 95
- List:Voltage 96
- Source Subsystem - Mode 98
- Source Subsystem - Phase 99
- Source Subsystem - PONSetup 100
- Source Subsystem - Pulse 104
- Source Subsystem - Voltage 107
- Status Subsystem Commands 113
- System Commands 117
- Trigger Subsystem 126
- Common Commands 131
- 5.1 *CLS 132
- 5.2 *ESE 133
- 5.3 *ESR? 133
- 5.4 *IDN? 134
- 5.5 *OPC 134
- 5.6 *OPT? 135
- 5.7 *PSC 136
- 5.8 *RCL 136
- 5.9 *RST 137
- 5.10 *SAV 138
- 5.11 *SRE 138
- 5.12 *STB? 139
- 5.13 *TRG 140
- 5.14 *WAI 140
- Programming Examples 141
- Programming the Output 142
- Power-on Initialization 142
- Enabling the Output 142
- AC Voltage and Frequency 142
- Programming the Output Phase 144
- Current Limit 144
- Waveform Shapes 145
- Individual Phases 146
- Coupled Commands 147
- FIXED mode 149
- STEP mode 149
- PULSE mode 149
- LIST mode 149
- Step and Pulse Transients 150
- List Transients 151
- Triggering Output Changes 153
- Trigger System Model 153
- Generating Triggers 155
- Acquiring Measurement Data 156
- Power Measurements 157
- Frequency Measurements 157
- Harmonic Measurements 158
- Triggering Measurements 159
- TRIGGER RECEIVED 160
- INIT[:IMM]:ACQ 160
- 4096 DATA POINTS 163
- Trigger System Summary 164
- Status Registers 165
- Questionable Status Group 168
- Standard Event Status Group 169
- Status Byte Register 169
- Examples 170
- SCPI Command Completion 171
- Option Commands 172
- IEC 1000-4-11 (-411) 173
- IEC 1000-4-13 (-413) 177
- IEC 1000-4-13 Subsystem 177
- Interharmonics Subsystem 188
- RTCA/DO-160D (-160) 190
- VOLTAGE SURGE, for detail 192
- VOLTAGE UNDER 192
- MIL-STD 704E (-704) 197
- AC System 197
- DC System 198
- Programming Considerations 198
- OMNI Reference Impedance 200
- Watt Hour Meter (-WHM) 201
- Current Sink Option (-SNK) 202
- SCPI Version 212
- Appendix C: Error Messages 213
- Table 8-4 : Error Messages 218
Powiązane produkty i podręczniki dla Ekwipunek Ametek BPS Series Programming Manual
Ekwipunek Ametek BPS Series Instrukcja Użytkownika
(153 strony)
(153 strony)
Ekwipunek Ametek M133 Instrukcja Użytkownika
(8 strony)
(8 strony)
Ekwipunek Ametek M130 Instrukcja Użytkownika
(99 strony)
(99 strony)
Ekwipunek Ametek CTS 3.0 Instrukcja Użytkownika
(166 strony)
(166 strony)
Ekwipunek Ametek CSW Series Instrukcja Użytkownika
(174 strony)
(174 strony)
Ekwipunek Ametek 2003RP Instrukcja Użytkownika
(126 strony)
(126 strony)
Ekwipunek Ametek 2001RP Instrukcja Użytkownika
(131 strony)
(131 strony)
Ekwipunek Ametek RS Series Instrukcja Użytkownika
(228 strony)
(228 strony)
Ekwipunek Ametek MX15 Series Instrukcja Użytkownika
(184 strony)
(184 strony)
Ekwipunek Ametek Lx Series II Instrukcja Użytkownika
(226 strony)
(226 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji