Ametek Lx Series II Programming Manual Instrukcja Użytkownika Strona 128
- Strona / 242
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Programming Manual Lx \ Ls Series II
124
Bit Position
7
6
5
4
3
2 - 0
Bit Weight
128
64
32
16
8
Table 5-3: Bit Configuration of Status Byte Register
OPER =
operation status
summary
MSS =
master status
summary
ESB =
event status byte
summary
RQS =
request for
service
QUES =
questionable status
summary
MAV =
message
available
Query Syntax *STB?
Returned Parameters <NR1> (Register binary value)
Related Commands *SRE *ESE *ESR
5.12 *TRG
This command generates a trigger to any subsystem that has BUS selected as its source (for
example, TRIG:SOUR BUS).The command has the same affect as the Group Execute Trigger
(<GET>) command.
Command Syntax *TRG
Parameters None
Related Commands ABOR INIT TRIG[:IMM]
5.13 *TST?
This query causes the AC Source to do a self-test and report any errors. The selftest will run until
the first error is encountered and terminate. The response to the query will either be the first error
encountered or 0 is no error was found. (Selftest passed). For a list of error messages, refer to
Appendix C.
Note: The selftest should always be run in 3 phase mode on all Lx models and Ls models with the
–MODE option. If the selftest is run in single phase mode, not all aspects of the Phase 2/B and
3/C hardware will be tested as a result. If the power source is a Ls-1 single phase only
configuration, the selftest can only be run in single phase mode.
Note: The following settings must be in effect before sending the *TST? Command:
OUTP 0 Output relay must be open
INST:NSEL ALL;:FUNC SIN On all Lx models and Ls models with the –ADV option, it is
required to set the waveform for all three phases to SIN
(sinewave).
VOLT:RANG MIN The LOW voltage range (135, 156 or 200) must be selected.
VOLT:ALC ON The ALC mode must be set to ON.
Note: The selftest is always performed at 400 Hz, 115 Vac. This is required to obtain the correct
internal test current based on the buit-in selftest loads. However, the output relay is open during
the selftest and no output is present on the output terminals during the selftest. At the end of the
selftest, the output relay remains open and the voltage is set to 0V. The frequence remains set to
400 Hz on Ls/Lx models with firmware revisions 0.97 or lower. On Lx/Ls models with firmware
revision 0.98 or higher, the programmed frequency will return to the value set before execution of
the selftest command.
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Powiązane produkty i podręczniki dla Ekwipunek Ametek Lx Series II Programming Manual
Ekwipunek Ametek MX CTSH Instrukcja Użytkownika
(151 strony)
(151 strony)
Ekwipunek Ametek i Series Instrukcja Użytkownika
(341 strony)
(341 strony)
Ekwipunek Ametek MX CTSL Instrukcja Użytkownika
(157 strony)
(157 strony)
Ekwipunek Ametek APG-XT Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Ametek PLA-PLW Instrukcja Użytkownika
(128 strony)
(128 strony)
Ekwipunek Ametek FPDC Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek ACPS Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek HPAL Instrukcja Użytkownika
(3 strony)
(3 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji