Ametek Lx Series II Programming Manual Instrukcja Użytkownika Strona 98
- Strona / 242
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Programming Manual Lx \ Ls Series II
94
VOLTage:PROTection
Phase Selectable
This command sets the overvoltage protection (OVP) level of the AC source. If the peak output
voltage exceeds the OVP level, then the AC source output is disabled and the Questionable
Condition status register OV bit is set (see Section 7 under Programming the Status and Event
Registers). An overvoltage condition can be cleared with the OUTPut:PROTection:CLEar
command after the condition that caused the OVP trip is removed. The OVP always trips with zero
delay and is unaffected by the OUTPut:PROTection:DELay command.
Command Syntax [SOURce:]VOLTage:PROTection[:LEVel]<NRf+>
Parameters 0 to 500
Unit V (peak voltage)
*RST Value MAX
Examples VOLT:PROT 400 VOLT:PROT:LEV MAX
Query Syntax [SOURce:]VOLTage:PROTection[:LEVel]?
Returned Parameters <NR3>
Related Commands OUTP:PROT:CLE
VOLTage:RANGe
Phase Selectable
This command sets the voltage range of the AC source. Two voltage ranges are available: a 150
volt range and a 300 volt range. Sending a parameter greater than 150 selects the 300 volt range,
otherwise the 150 volt range is selected.
When the range is set to 150, the maximum rms voltage that can be programmed for a sine wave
is 150 volts. For other waveshapes, the maximum programmable voltage may be different,
depending on the waveform crest factor.
The VOLTage:RANGe command is coupled with the CURRent command. This means that the
maximum current limit that can be programmed at a given time depends on the voltage range
setting in which the unit is presently operating. Refer to chapter 4 under "Coupled Commands" for
more information.
A user settable delay may be inserted between dropping the output voltage to zero and changing
the range relay state. See the “PONSetup:RELay” command for details. Your application program
should allow for this delay. (default is 0.1 sec or 100 msec).
Command Syntax [SOURce:]VOLTage:RANGe<NRf+>
Parameters 150 | 300
*RST Value MAX
Examples VOLT:RANG 150 VOLT:RANG MIN
Query Syntax [SOURce:]VOLTage:RANGe?
Returned Parameters <NR3>
Related Commands VOLT PONS:REL
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Powiązane produkty i podręczniki dla Ekwipunek Ametek Lx Series II Programming Manual
Ekwipunek Ametek MX CTSH Instrukcja Użytkownika
(151 strony)
(151 strony)
Ekwipunek Ametek i Series Instrukcja Użytkownika
(341 strony)
(341 strony)
Ekwipunek Ametek MX CTSL Instrukcja Użytkownika
(157 strony)
(157 strony)
Ekwipunek Ametek APG-XT Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Ametek PLA-PLW Instrukcja Użytkownika
(128 strony)
(128 strony)
Ekwipunek Ametek FPDC Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek ACPS Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek HPAL Instrukcja Użytkownika
(3 strony)
(3 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji