Ametek Lx Series II Programming Manual Instrukcja Użytkownika Strona 182
- Strona / 242
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Programming Manual Lx \ Ls Series II
178
8.2.12 Examples – APE Query Commands
The TLK header will setup the AC Power System to talk data. The TLK header will setup the AC
Power System to report a programmed output parameter if the program header is the argument for
the TLK header.
To setup the AC Power System to report a measured value, attach a measurement header as the
TLK argument. The measurement headers are VLT, CUR, PWR, APW and PWF with an A, B or C
extension and FQM with no extension.
Note: Unlike the California Instruments L Series controllers, sending a TLK XXX command to the Ls
Controller will not cause the front panel to display the measurement screen. This is due to the
different measurement screen layout and organization of the Ls series controller versus the L series
controller.
The following string will setup the AC Power System to measure the phase A power output when it is
talk addressed:
TLK PWR A
All arguments for the TLK header are shown in Table 3-13. Table 3-14 shows an example response
for all TLK arguments with no A, B or C extension. For 1-phase systems, all responses will only
include the phase A value. For 3-phase systems, if the TLK argument includes the A, B or C
extension, the response message will be only for the indicated phase.
A GPIB Service Request (SRQ) will be generated at the completion of a measurement if the SRQ2
header is included with the TLK string. The following string will cause the Service Request to be
generated when the power system has finished the power factor measurement.
TLK PWF SRQ2
Example talk responses are shown in Table 8-5.
Command
Response (Fields separate by SPACE 0x20 characters)
Field A
Field B
Field C
TLK
ALM
ALMA0000
B135.0
C270.0
TLK
AMP
AMPA000.0
B000.0
C000.0
TLK
APW
APWA1003
B0985
C1507
TLK
CFG
CFGA0001
B0028
C0120
TLK
CLM
CLMA11.12
B0002
C0000
TLK
CRL
CRLA11.12
B11.12
C11.12
TLK
CUR
CURA06.14
B05.12
C06.71
TLK
ELT
ELTH0147
M0051
S0033
TLK
FLM
FLMA0060
B0045
C0550
TLK
FQM
FQM59.97
TLK
FRQ
FRQ60.00
TLK
CLK
CLK INT (*)
TLK
SNC
SNC INT
TLK
PHZ
PHZA000.0
B240.0
C120.0
TLK
PWF
PWFA1.000
B1.000
C1.000
TLK
PWR
PWRA0.737
B0.620
C0.806
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Powiązane produkty i podręczniki dla Ekwipunek Ametek Lx Series II Programming Manual
Ekwipunek Ametek MX CTSH Instrukcja Użytkownika
(151 strony)
(151 strony)
Ekwipunek Ametek i Series Instrukcja Użytkownika
(341 strony)
(341 strony)
Ekwipunek Ametek MX CTSL Instrukcja Użytkownika
(157 strony)
(157 strony)
Ekwipunek Ametek APG-XT Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Ametek PLA-PLW Instrukcja Użytkownika
(128 strony)
(128 strony)
Ekwipunek Ametek FPDC Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek ACPS Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek HPAL Instrukcja Użytkownika
(3 strony)
(3 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji