Ametek Lx Series II Programming Manual Instrukcja Użytkownika Strona 71
- Strona / 242
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Programming Manual Lx \ Ls Series II
67
4.14 Power On Subsystem
This subsystem controls the specific configuration settings at power on. Most power on settings
are determined by the power on register recall state using the OUTPut:PON:STATe command.
Some aspects are not part of a register however and must be controlled using the PONS
commands.
Subsystem Syntax
[SOURce:]PONSetup
:CLOCk STD | MAST | AUX
:PEAK:CURRent[:PROTection] Disables peak current protection.
:RELay:HOLD Sets output off relay open delay in seconds.
:SYNChronize[:SOURce] EXTernal | LINE
PONSetup:CLOCk
This command is used to set the clock and lock mode at power up. It is factory set and should not
be changed unless the configuration has been modified in the field. Units with the –LKM option
are fixed to MAST mode. Units with the –LKS option can be set to either STANdalone or AUX.
When set to AUX, the –LKS unit will power up in external clock mode. When set to STANDalone,
the –LKS unit will power up in internal clock mode. The –LKM unit always powers up in internal
clock mode. It‟s clock state cannot be changed.
Command Syntax PONSetup:CLOCk
Parameters STANdalone | MASTer | AUXiliary
Examples PONS:CLOC
Query Syntax PONS:CLOC?
Returned Parameters <CRD>
Related Commands None
PONSetup:PEAK:CURRent[:PROTection]
This command can be used to disable the peak current shutdown mode. It is factory disabled and
should be left disabled for most situations. This command is not available on the
HP6834B/CI4500iL.
Command Syntax PONSetup:PEAK:CURRent[:PROTection]
Parameters 0 | 1 | OFF | ON
Examples PONS:PEAK:CURR 1
Query Syntax PONS:PEAK:CURR?
Returned Parameters 0 | 1
Related Commands OUTP:PROT:DEL
PONSetup:SYNChronize[:SOURce]
This command can be used to set the initial sync mode between External Sync or Line Sync. This
requires the –EXT or –LNS option respectively. This command is supported in firmware revision
1.50 and higher.
Command Syntax PONSetup:SYNChronize:[:SOURce]
Parameters EXTernal | LINE
Examples PONS:SYNC:SOUR EXT
Query Syntax PONS:SYNC:SOUR?
Returned Parameters <CRD>
Related Commands FREQuency:MODE SENSe
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Powiązane produkty i podręczniki dla Ekwipunek Ametek Lx Series II Programming Manual
Ekwipunek Ametek MX CTSH Instrukcja Użytkownika
(151 strony)
(151 strony)
Ekwipunek Ametek i Series Instrukcja Użytkownika
(341 strony)
(341 strony)
Ekwipunek Ametek MX CTSL Instrukcja Użytkownika
(157 strony)
(157 strony)
Ekwipunek Ametek APG-XT Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Ametek PLA-PLW Instrukcja Użytkownika
(128 strony)
(128 strony)
Ekwipunek Ametek FPDC Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek ACPS Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek HPAL Instrukcja Użytkownika
(3 strony)
(3 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji