Ametek Lx Series II Programming Manual Instrukcja Użytkownika Strona 234
- Strona / 242
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Programming Manual - Rev S Lx \ Ls Series II
230
Number
Message String
Cause
Remedy
604
"Trigger received before
requested number of
pre-trigger readings"
Data acquisition pre-
trigger buffer not
filled yet.
Hold off trigger or reduce pre-trigger
delay.
605
"Requested RMS current
too high for voltage
range"
Max RMS current is
function of voltage
range selected.
Reduce programmed RMS current
limit or select low voltage range.
606
"Waveform data not
defined"
No waveform name
specified
Specify waveform name before
sending waveform data.
607
"VOLT,VOLT:SLEW, and
FUNC:SHAPe modes
incompatible"
Conflict between
wave shape and
programmed slew
Reduce slew or change waveform
type.
608
"Measurement
overrange"
Measurement data
out of range.
609
"Output buffer overrun"
Too much data in
output buffer.
Check receive mode on application
program. Program is not reading data
sent by AC source.
610
"Command cannot be
given with present
SYST:CONF setting"
Command conflicts
with available
hardware or firmware
option settings.
Check configuration for available
options and features.
801
"Output volt fault"
- Output voltage does
not match program
value when ALC is
on.
- Over load
- Voltage kick-back
- No output voltage
Load exceeds current limit and unit is
in Constant Voltage (CV) mode of
operation. Reduce load or increase
CL setting.
Output voltage is driven above
programmed voltage by external
influence (Load, voltage kickback,
etc.)
802
"Current limit fault"
Current limit
exceeded.
Load exceeds current limit and unit is
in Constant Voltage (CV) mode of
operation. Reduce load or increase
CL setting
803
"Temperature fault"
Amplifier heat sink
temp. too high.
Reduce load. Ensure proper air flow
and exhaust clearance. Check fan(s)
for operation.
804
"External sync. error"
Could not sync to
external sync signal.
External sync signal missing,
disconnected or out of range.
805
"Initial memory lost"
Initial settings could
not be recalled at
power-up.
Save power on settings again to
overwrite old content.
806
"Limit memory lost"
Hardware
configuration settings
could not be recalled
at power-up.
Contact AMETEK service department
at service@programmablepower.com
to obtain instructions on restoring
configuration data.
807
"System memory lost"
Memory corrupted
during power-up.
Recycle power.
808
"Calibration memory lost"
Calibration data lost
during power-up.
Contact AMETEK service department
at service@programmablepower.com
to obtain instructions on restoring
calibration data or recalibrate unit.
813
"Missing list parameter"
One or more
transient list
parameters missing.
Check programmed lists.
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Powiązane produkty i podręczniki dla Ekwipunek Ametek Lx Series II Programming Manual
Ekwipunek Ametek MX CTSH Instrukcja Użytkownika
(151 strony)
(151 strony)
Ekwipunek Ametek i Series Instrukcja Użytkownika
(341 strony)
(341 strony)
Ekwipunek Ametek MX CTSL Instrukcja Użytkownika
(157 strony)
(157 strony)
Ekwipunek Ametek APG-XT Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Ametek PLA-PLW Instrukcja Użytkownika
(128 strony)
(128 strony)
Ekwipunek Ametek FPDC Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek ACPS Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek HPAL Instrukcja Użytkownika
(3 strony)
(3 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji