Ametek Lx Series II Programming Manual Instrukcja Użytkownika Strona 46
- Strona / 242
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Programming Manual Lx \ Ls Series II
42
4.6 Instrument Subsystem
This subsystem programs the three-phase output capability of the AC Power Source.
Subsystem Syntax
INSTrument
:COUPle ALL | NONE Couple all phases for programming
:NSELect <n> Select the output phase to program (1|2|3)
:SELect <output> Select the output phase to program (OUTP1|OUTP2|OUTP3)
INSTrument:COUPle
In a three-phase power source it is convenient to set parameters of all three output phases
simultaneously with one programming command. When INST:COUP ALL is programmed,
sending a command to any phase will result in that command being sent to all three phases.
INSTrument:COUPle only affects the operation of subsequent commands. It does not by itself
immediately affect the AC source's output. The commands that are affected by
INSTrument:COUPle are those with the designation: Phase Selectable.
INSTrument:COUPle has no affect on queries. There is no way to query more than one phase
with a single command. Directing queries to individual phases is done with INSTrument:NSELect.
Command Syntax INSTrument:COUPle<coupling>
Parameters ALL|NONE
*RST Value ALL
Examples INST:COUP ALL
Query Syntax INSTrument:COUPle?
Returned Parameters <CRD>
Related Commands INST:NSEL
INSTrument:NSELect
INSTrument:SELect
These commands allow the selection of individual outputs in a three-phase model for subsequent
commands or queries. Their operation is dependent on the setting of INSTrument:COUPle. If
INST:COUP NONE is programmed, then the phase selectable commands are sent only to the
particular output phase set by INSTrument:NSELect. If INST:COUP ALL is programmed, then all
commands are sent to all three output phases.
Note: If the power source is in SINGLE phase mode or does not support 3 phase mode of
operation, an INST:NSEL 2 or INST:NSEL 3 command will result in a –222,”Data out of range”
error.
INSTrument:NSELect selects the phase by its number, while INSTrument:SELect references it by
name. These commands also select which output phase returns data when a query is sent.
Command Syntax INSTrument:NSELect <NR1>
INSTrument:SELect <output>
Parameters For INST:NSEL: 1 | 2 | 3
For INST:SEL: OUTPut1 | OUTPut2 | OUTPut3
*RST Value 1 or OUTPut1
Examples INST:NSEL 3
Query Syntax INSTrument:NSELect?
Returned Parameters <NR1>
Related Commands INST:COUP
- Lx \ Ls Series II 1
- AC Power Source 1
- Programming Manual 1
- SAFETY SYMBOLS 7
- Table of Contents 9
- Table of Figures 11
- Table of Tables 11
- 1. Introduction 12
- 1.2.1 Firmware differences 13
- 1.2.2 Hardware differences 13
- 2. Introduction to SCPI 16
- 2.2.3 The SCPI Command Tree 17
- 2.3 Using Queries 19
- 2.4 Coupled Commands 19
- 2.5.3 Headers 20
- 2.5.4 Query Indicator 21
- 2.5.6 Root Specifier 21
- 2.5.7 Message Terminator 21
- 2.6 SCPI Data Formats 22
- 3. System Considerations 24
- 3.2 USB Interface 25
- 3.2.2 USB Interface Use 31
- 3.3 LAN Option 32
- 3.3.5 Socket Port Number 36
- 3.4 RS232C Serial Interface 37
- 4. SCPI Command Reference 39
- 4.2 Subsystem Commands 40
- 4.3 Calibration Subsystem 41
- 4.4 Diagnostic Subsystem 43
- 4.5 Display Subsystem 44
- 4.6 Instrument Subsystem 46
- 4.7 Limit Subsystem 47
- 4.13 Output Subsystem 66
- 4.14 Power On Subsystem 71
- 4.24 System Commands 109
- 4.26 Trigger Subsystem 117
- (default) 118
- 5. Common Commands 122
- 5.1 *CLS 123
- 5.2 *ESR? 123
- 5.3 *IDN? 124
- 5.4 *OPC 124
- 5.5 *OPT? 124
- 5.6 *PSC 124
- 5.7 *RCL 125
- 5.8 *RST 126
- 5.9 *SAV 127
- 5.10 *SRE 127
- 5.11 *STB? 127
- 5.12 *TRG 128
- 5.13 *TST? 128
- 5.14 *WAI 129
- 6. Programming Examples 130
- 6.2.1 Waveform Shapes 132
- 6.2.2 Individual Phases 133
- 6.3 Coupled Commands 134
- FIXED mode 136
- STEP mode 136
- PULSE mode 136
- LIST mode 136
- 6.6 List Transients 138
- INIT[:IMM] 140
- 6.7.7 Generating Triggers 142
- 6.8 Making Measurements 143
- 6.8.2 Power Measurements 144
- 6.8.3 Harmonic Measurements 144
- Offset = 151
- 0 to 2^9 151
- Offset = - 4096 151
- Offset = - 2048 151
- Offset = 0 151
- 6.10.2 Download Sample 152
- 7.1 Power-On Conditions 154
- 7.2 Operation Status Group 154
- 151 155
- 7.6 Status Byte Register 160
- 7.7 Examples 161
- 7.8.1 Remote Inhibit (RI) 164
- 7.9 SCPI Command Completion 165
- 8. Option Commands 166
- 8.2.1 Introduction 167
- 8.2.3 GPIB Address 170
- 8.2.4 APE over RS232 170
- 8.2.5 Message Format 171
- 8.2.6 Numeric Data Field 171
- 8.2.7 Program Headers 172
- 8.2.9 APE Program Headers 174
- 8.2.14 Service Requests 184
- 181 185
- 8.3.1 Introduction 187
- 8.3.2 ABLE Language details 187
- 8.3.3 Language Extension 191
- 8.4 RTCA/DO-160D (-160) 192
- VOLTAGE SURGE, for details 194
- 8.6.1 Command Tree 200
- 8.7.1 Command Tree 207
- 219 223
- 220 224
- 221 225
- 222 226
- SCPI Version 227
- SCPI Confirmed commands 227
- 225 229
- PONS:SYNC[:SOUR] 229
- Appendix C: Error Messages 230
- 227 231
- 228 232
- 229 233
- 230 234
- 231 235
Powiązane produkty i podręczniki dla Ekwipunek Ametek Lx Series II Programming Manual
Ekwipunek Ametek MX CTSH Instrukcja Użytkownika
(151 strony)
(151 strony)
Ekwipunek Ametek i Series Instrukcja Użytkownika
(341 strony)
(341 strony)
Ekwipunek Ametek MX CTSL Instrukcja Użytkownika
(157 strony)
(157 strony)
Ekwipunek Ametek APG-XT Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Ametek PLA-PLW Instrukcja Użytkownika
(128 strony)
(128 strony)
Ekwipunek Ametek FPDC Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek ACPS Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Ametek HPAL Instrukcja Użytkownika
(3 strony)
(3 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji